张家口宣化北伦平衡机制造有限公司

Xuanhua Beilun Balancing Machinery Co Ltd

 
ENGLISH 企业概况    平衡机描述 新产品介绍 资料下载 技术介绍 联系我们 第2网页

风机叶轮平衡机

 通用平衡机

 

 电脑电测箱

 HP-15

 硬支承平衡机计算机电测仪

 

 摩擦磨损试验机

 

 重型平衡机

 

 汽车行业

 

 专用平衡机

 

 旋转机械振动

各种转子平衡工艺

 

         

YFW-500A hard support FRP fan balancer


This machine is a permanent standard hard bearing balancing machine-----

The rotor with different shape and weight does not need to be recalibrated. The magnitude and angle of the unbalance can be measured at one start.

Yfw-500a FRP fan impeller balancing machine is a kind of balancing machine specially designed and manufactured by our factory for FRP fan manufacturer. This machine is designed for horizontal hard support, universal joint drive, digital display automatic measurement electric meter and other general forms. The measurement part of the balancing machine adopts the closed force sensor, which has the advantages of non-collision, high sensitivity and durability, and good low-speed measurement performance. In addition to the characteristics of general horizontal hard bearing balancing machine, two important parameters are given specially for the balancing characteristics of fan impeller. First, the maximum balance rotor diameter is 1800 mm, and second, the maximum rotor mass is 500 kg. These two parameters determine that the machine can detect most of the dimensions with the highest sensitivity for the impeller of the machine.

Refer to the operation manual of yfw-500a FRP fan impeller balancer for the detailed description of the machine. The main technical parameters are as follows:

1. Rotor mass range: 10-500kg

2. Maximum rotor diameter: Φ 1800 mm

3. Maximum bearing shaft diameter: Φ 10 -- 90mm

4. Maximum bearing length: 1500 mm

5. Balanced working speed: 100-800 rpm

6. Minimum achievable residual unbalance: 1g. Mm / kg

7. Motor power: 4 kW frequency converter speed regulation---vvvf

8. Power supply: 380V, 50Hz

 

YFW-500A型 硬支承玻璃钢风机平衡机

 

本机是永久标定型硬支承平衡机-----

换不同形状与重量的转子是不需要重新标定的,一次启动即可测量不平衡量值的大小与角度。

  YFW-500A型玻璃钢风机叶轮平衡机是本厂针对玻璃钢风机制造厂专门设计制造的一种平衡机。本机设计为卧式硬支承、万向节传动、数字显示自动测量电测仪等通用形式。平衡机的测量部分采用了封闭式测力传感器:它具有不磕碰、灵敏度高经久耐用、低速测量性能好等优点。除具有通用卧式硬支承平衡机的特点之外,还专门针对风机叶轮的平衡特点给定了两个重要参数。其一,最大平衡转子直径1800毫米,其二,最大转子质量500公斤,这两个参数决定了本机能以最高灵敏度检测绝大部分尺寸适用于本机的叶轮。

本机详细说明参见《YFW-500A型玻璃钢风机叶轮平衡机使用说明书》,主要技术参数如下∶

1.转子质量范围: ………………………………… 10-500 公斤

2.最大转子直径: ……………………………………Φ1800 毫米

3.最大支承轴径: …………………………………Φ10--90 毫米

4.最大支承长度: ………………………………………1500 毫米

5.平衡工作转速: …………………………………… 100-800 转/分

6.最小可达剩余不平衡量:……………………………1 克.毫米/公斤

7.电机功率: ………………………………   4 千瓦 变频器调速

8.电源: …………………………………………… 380伏、50赫兹

   RSQ-5  RYQ-5 YYQ-5  YYQ-16  YYQ-50  YYQ-100  YYQ-160  YYQ-300  YYQ-1000  YYQ-5000 
 

 

Hp-16 hard support balancing machine computer electrical testing meter

(single interface displays all contents and own all software and hardware intellectual property rights)


Upgrade software in 2018, realize fast measurement mode, more suitable for batch operation process

The function of automatic detecting sensor signal line fault

Automatic measurement, automatic memory, automatic stop

Open the memory key after starting the machine, directly measure the dynamic balance data, input or modify the parameters such as a, B, C, R2, R1 support mode after the memory stops, and the electric measuring box will automatically recalculate the separation results.

After parking, you can see the static unbalance value.

When the speed is set, it can automatically judge that the measured data is stable and effective. If the data is stable, the electric measuring box will automatically memorize it.

At the set speed, enter the data measurement and memory independently, and then drive the main engine to stop automatically.

In case of power failure, the last memorized measurement data shall be retained: restart the machine --- the electric measuring box displays the last memorized measurement data.

Self test function of measuring system.

The magnification of the automatic control system is convenient for some process requirements requiring fast operation.

It can be used to solve the balance problem of non ideal rotor.

Customer calibration can be carried out in accordance with the procedure, and the influence coefficient can be calculated automatically.

If the customer's calibration rotor is not in good condition and the calibration is not ideal, the factory calibration status can also be restored.

Electronic factory report document.

HP-16 硬支承平衡机计算机电测仪

(单界面显示全部内容、自有全部软硬件知识产权)

2018升级软件,实现快速测量模式,更适于批量操作工艺

自动检测传感器信号线故障的功能

自动测量,自动记忆,自动停机

  1. 开机后打开记忆键,直接测量动平衡数据, 记忆停车后再输入或修改a,b,c,r2,r1支承方式等参数,电测箱会自动重新计算分离结果。

  2. 停车后可以看静不平衡量值。

  3. 在设定转速自动判断测量数据稳定有效,如果数据稳定电测箱便自动记忆 

  4. 在设定转速,自主进入数据测量,自主数据记忆 ,而后可以自动驱动主机停机

  5. 停电保留最末一次记忆的测量数据:再次开机---电测箱显示上次记忆的测量数据

  6. 测量系统自检功能。

  7. 自动控制系统的放大倍数,便于一些要求快速操作的工艺要求。

  8. 可以解决非理想转子的平衡解算问题。

  9. 客户标定,可以按照程序进入顺序标定,自动计算影响系数。

  10. 如果客户标定转子状况不佳 、标定不理想,也可以恢复出厂标定状态。

  11. 电子出厂报告文件

 

Address: Wanfeng Rd Dongmenwai Str. Xuanhua Hebei  Province China

Post code:075100

E-mail: cdf@beilun.com.cn

Tel: +86 313-3112400  

       +86 313 3175800

Fax: +86 313 3175900

http://www.beilun.com.cn/indexe.htm

 

张家口宣化北伦平衡机制造有限公司

地 址: 河北省宣化区东门外万丰路

邮政编码: 075100

联系电话: 0313-3112400 3175800

传真:0313-3175900

互联网站: http://www.beilun.com.cn

E-mail:cdf@beilun.com.cn